westernsubaruclub.com

Vendor Marketplace => Automotive Parts and Services => BetaCuts Custom Vinyl Decals => Topic started by: BetaCuts on September 06, 2012, 03:54:01 PM

Title: Need your help for TMIC stencil measurement
Post by: BetaCuts on September 06, 2012, 03:54:01 PM
Anyone have a factory IC with the STI on it?

I'm going to be making stencils so that you guys and gals can paint them.

I need the height and width of the original painted one.

Thanks
Title: Re: Nees your help for TMIC stencil measurement
Post by: energie on September 06, 2012, 04:09:59 PM
Lemme go measure the one in my garage brb lol
Title: Re: Nees your help for TMIC stencil measurement
Post by: energie on September 06, 2012, 04:22:05 PM
6 inch 9/16 for the width
18 inch 7/16 for length
For the rectangular opening of the top mount.
Both measurements are allowing a 1/16 inch clearance For the stencil to drop in.

The Sti logo is 9 inch 3/4 wide at the bottom and 3 inch 5/8 tall

Hope this is what you needed.
Title: Re: Nees your help for TMIC stencil measurement
Post by: LilDrunkenSmurf on September 07, 2012, 10:50:21 AM
I still have the OEM intercooler with STi logo if you want to check it out.
Title: Re: Nees your help for TMIC stencil measurement
Post by: snackers on September 07, 2012, 10:59:35 AM
In case this helps...

(http://www.baneon.org/steve/misc/STi/WRX_STI_Intercooler.jpg)

Quote
A= 18-1/2"
B= 6-3/4"
C= 3-1/16"
D= 1-1/2"
E= 12-1/8"
F= 4-5/8"
http://www.iwsti.com/forums/general/138102-intercooler-logo-measurements.html

There are lots of threads like this over there. Some of them probably even give you exact letter width and spacing too.
Title: Re: Nees your help for TMIC stencil measurement
Post by: Motohead on September 07, 2012, 12:40:09 PM
Quote from: BetaCuts on September 06, 2012, 03:54:01 PM
Anyone have a factory IC with the STI on it?

I'm going to be making stencils so that you guys and gals can paint them.

I need the height and width of the original painted one.

Thanks

Sweet! Good on you!

Quote from: energie on September 06, 2012, 04:09:59 PM
Lemme go measure the one in my garage brb lol


Gotta stop skim reading, at first glance I thought you said "in my garbage". Was gonna jump up and down and say "yo, throw that itshay this way!"

LOL!
Title: Re: Nees your help for TMIC stencil measurement
Post by: energie on September 07, 2012, 01:07:33 PM
Quote from: Motohead on September 07, 2012, 12:40:09 PM
Sweet! Good on you!


Gotta stop skim reading, at first glance I thought you said "in my garbage". Was gonna jump up and down and say "yo, throw that itshay this way!"

LOL!

Hahahah I'm selling it of your interested
Title: Re: Nees your help for TMIC stencil measurement
Post by: Motohead on September 07, 2012, 01:27:00 PM
I'm good, but thanks for the offer bro!
Title: Re: Nees your help for TMIC stencil measurement
Post by: BetaCuts on September 11, 2012, 03:26:25 PM
Damn you're good, thanks for posting this.
 
Anyways, I'll be selling stencils for $15 shipped or $13 picked up.
It will use paint mask vinyl which is lower tack and removeable once the painting has been done.

Unfortunately not re-useable, unless you're careful and can place the vinyl back onto the paper it came on without tearing things.

Brennan


Quote from: snackers on September 07, 2012, 10:59:35 AM
In case this helps...

(http://www.baneon.org/steve/misc/STi/WRX_STI_Intercooler.jpg)
http://www.iwsti.com/forums/general/138102-intercooler-logo-measurements.html

There are lots of threads like this over there. Some of them probably even give you exact letter width and spacing too.