Hey guys! My name Is Blaine and I Imported a JDM GDB Bugeye.
I imported the car with Brian from B-Pros help. I got the car Nov. 7 but had parts ordered the last week of october.
Everything is done on the car as of Nov 28th
Specs:
2000 STi Bugeye 87,xxx KM
EJ207 6 speed/brembos
Defi Genome Boost, Oil Pressure, Oil Temp Gauges
STi Struts with lowering springs
Installed/Own/
Ordered/
PlannedGroup N Engine Mounts
Group N Transmission Mount
Perrin Pitchstop
Whiteline 22mm front swaybar/bushings
Whiteline 22MM rear swaybar/bushings (Fit, I think, though looks funny)
Whiteline Adjustble front endlinks
Whiteline rear swaybar mount
Whiteline rear endlinks
Perrin Intercooler->TB coupler
Kartboy Front and Rear Stay Bushings
Whiteline Transmission Crossmember Bushings
Invidia Bellmouth Catless Downpipe (Fit, but caused boost creep)
Invidia Street N1 Catback W/ Ti Tip
Perrin Short Ram Intake (Fit, perfectly before Perrin Turbo Inlet. Sits okay now)
Perrin Turbo Heat Shield (Did not fit, needed modification)
GrimmSpeed Hood Struts
SYM Dash Gauge Pod
Innovate Air/Fuel Ratio Gauge
Glowshift Watertemp Gauge
Whiteline Steering Rack Bushings
Perrin Pulley Cover
Perrin Radiator Shroud (Fit, until installed new mishi rad and doesnt fit.)
Perrin Battery Tie Down
Perrin Oil Fill Cap
Block Heater
Spark Plugs
Mishimoto X-line Performance Rad (Fit. but sits highish)
Mishimoto Silicone Hose Kit (Kinda Fit, freaking fight get them on and find where they go)
Perrin Coolant Overflow Tank
Gates OE Water Pump and Timing Belt Kit (02WRX)
Grimmspeed lightweight Crank Pulley and removal tool
Intake Spacers (Fit, but such a fight and headache not sure if worth.)
PCV Valve 02 wrx
IAG Caps (Some fit. Coolant rattled on aluminum overflow, Brake and Wiper did.)
Perrin Turbo Inlet (Fit but such a fight to get into spot and made Sram sit funny)
Battery Tie Down Bolts from Rallytech
License Plate Delete from Rallytech for gd (Did Not Fit)
Exedy Lightweight Clutch and Flywheel
Metal Oil Seperator Plate (Already Installed)
Perrin Reverse Lockout
Internal Shift Bushings
External Shift Bushings
Stainless Steel Clutch Line
Stainless Steel Brake Lines
Perrin Subframe Lockout kit
Beatrush Propeller Shaft Bushings
Killer B Oil Pickup
TiC Fender Cowl Braces
Cobb Uppipe (Fit wouldnt seal with Borla)Grimm Speed Upipe with EWG (Did not fit, hits steering knuckle)
EWG Tial (Did not fit.)
UEL Borla Headers (Fit but wouldnt seal with Cobb uppipe)
Grimm Speed Uppipe with Flex (Fit but seal was hard to obtain)
Perrin Rad Stays
Whiteline Front Roll Center Adjustment
Whiteline Anti Lift Kit Comfort
Whiteline Front Control Arm Bushing
Perrin Short Shifter
Group N Top Hats
NRG Short Hub Adapter
NRG Quick Release 2.5
NRG Steering Wheel
Spec C steering rack
Stock ECU Tune able!
Dyno TuneWell Ask me any questions, I do plan on going to the Tims meets once I get this
leaking radiator problem sorted out. Fixed it with a used one from the fourms and now that one is leaking. I hate oem rads.
My favourite mod are the hood struts. Closing the hood is a pit of a pain in the assay as I have to close it from the side first, but that prop rod is ugly. Or its tied with the rounded sway bar bolt.
Thanks!
Finished Pictures
Sorry Kyle but its staying in for now...
OIL CHANGE NOV. 11 875XX KM
Ram Installed at 875XX KM
Cabin Air Filter 875xx KM
All at 92000, Spark Plugs, Oil change, Timing Belt, PCV Valve (02 wrx), Multiple coolant flushes
92500 Ram Clean
93200 Vex installed new exedy clutch and light weight flywheel
95200 Oil change, MAF cleaned
100800 Oil change
102165 New tires because costco warranty/ Cabin air / Heated Seats
105000 Oil change and front lower ball joints
107000 Front Suspension updated, short shifter, new o2 for wideband.
April 2 Alignment at Lakeview Auto
108000 Valve cover gaskets and spark plugs/ fuel filter
108500 Four new coil packs and air filter cleaned
110000 Spec c steering rack, all four shocks replaced, new front wheel bearings and alignment at Lakeview Oct 28